I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I am a newbie to the Nordic development ecosystem. Just purchased a nRF52840-DK board and followed the instructions here:
https://infocenter.nordicsemi.com/index...
Hello,
Is there a way I can run JVM on nrf51 or nrf52 series devices? I have been searching the forums and did not find any updates on the same.
Any OS like embedded linux...
Hi,
We are currently in development of an IoT solution using the nRF9160. We are doing a set of EMC tests to ensure electromagnetic compatibility of the device. The test...
Hello,
I am trying to transfer a signal sampled on AN0 (P0.02) at 16kHz via Bluetooth using an ATT MTU of 247 and a 2MBPS PHY speed. The basis project used is examples ...
Hi, I am interested in using the NRF91 in our new products. So far I have modified the Asset_tracker example to send my custom data instead of sending the "sensor data". The...
Hi.
I have a question related to the Zigbee SDK's "On / Off Switch" example.
Studying the example, I cannot understand how to activate the "light_switch_send_on_off" function...
I'm trying to find out if the nRF52840 has the features needed for a new product. We need to be able to do the following from a Windows 7 or 10 program: scan for nearby BLE...
Hello,
I'm working on a project that makes use of both Bluetooth Service UUIDs like BAS and customer Service UUIDs. In the Bluetooth CCSv7 at Part A, Section 1.1, I found...
Hi,
our application is nearly finnished now, but I noticed, that after adding the secure_ble bootloader, the program enters the bootloader at poweron, then enters my application...
Hi, I got the schematic of thingy:92.
Now I have a question about netnabel: IF_SWD.
IF_SWD is connected to three nRF52840 GPIOs.
if the CTRL is high in IF_SWD, IF_SWD...
Hello,
I'm trying to use the USB MSC to show up as a file system, transfer the file into RAM, and send the file via BLE to an Android phone. This is with SDK 15.3 and S140...
Working with Fanstel BT840 module we have discovered that ADC channel VDD reads as zero or produces small mV level result. nRF52840 chip revision on these modules is QIAA...
Hello everyone,
i want to send a 16 Byte datapaket from a peripheral nRF52840 DK to my iPhone. (S140 SoftDevice) Im looking for an example who sends datapakets from peripheral...
