Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I have an application where knowledge of the current date/time is important. This is implemented by the central passing the time to the peripheral when it initially connects...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
Hi everyone,
I am currently working on a project that leads me to save a respectful amount of data.
Some of the objects that I save size a few KB actually.
I would...
Estimate battery life for FOB CR 2032 -240 mAh
We are developing remote with CR2032 battery and using Nordic nrf51-1822 BLE, 960 m sec connection interval, RX 1 packet...
I want to use nRF52840 Device to implement non-connectable advertisement and scan on one board.
To be more specific, I want to advertise information for some time period...
I am using NRF52 SDK14.0 and SoftDevice S132 v5.0.0. Application freezes somewhere in SoftDevice if sd_softdevice_enable() is called after nrf_drv_clock_lfclk_request() was...
Hello All,
Where would I find a library file for a PID controller? Forgive me if there is an obvious answer. I'm new to working with Keil.
Thanks for taking the time...
We need to put the processor in sleep mode (to conserve battery power) and wake-up the processor when the user touches the Cap Sensor pad.
Can you Cap Sensor in nrf52 be...
I'm using "nrf5_SDK_for_Mesh_v0.9.2-Alpha". And, I build examples using "SEGGER Embedded Studio 3.26a".
Now I want to modify examples for my custom board.
In CMake, "...
Hi, a little background information first, when debugging ble mesh example 0.9.x:
devzone.nordicsemi.com/.../
I'm now kinda having a massive problem with this function...
Hi,all.
I am using nRF52832.
Does the nRF52832 support dual mode that allows simultaneous advertising and scanning?
Are there any examples you can refer to if you...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
