I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi, Nordic
I check bootloader_secure sample for SDK 12.1, in dfu_public_key.c
/* This file was generated with a throwaway private key, that is only inteded for a debug...
Device : nrf51822
Softdevice : S110 v7.0.0
Title says it all. Autoconnect is working fine on my Android phones when nrf51822 is always programmed BLE_GAP_ADV_TYPE_ADV_IND...
Hi,
I tried to program my NRF52 using the arduino IDE using the following instructions on github: github.com/.../arduino-nRF5
Soonafter, I realized I could not program...
Hi,
Using the nRFGo Studio software, I noticed this is actually running using the Qt framework that makes porting application between Windows, MacOSX and Linux really easy...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I have been trying to make the BLE bootloader example works without succes. I am getting stuck after uploading the Softdevices and the Bootloader.
Step by step...
Hello.
I am experimenting examples \ peripherals \ saadc.
It is nrf 52832.
I changed NRF_DRV_TIMER_INSTANCE (0) to NRF_DRV_TIMER_INSTANCE (1), though I tried changing the...
Setting the gatts_enable_params.service_changed to 0 when enabling softdevice removes (or rather doesn't add) the Service Changed characteristic. That's what I want. However...
I'm developing a device based on an nrf52 chipset, and I'm experiencing strange behaving of the Radio interface. The firmware is based on SDK v11 and SoftDevice 132, the hardware...
Line 73 in function nrf_drv_rtc_init snippet bellow checks for UNINIT state. It accesses the m_cb array which is an uninitialized global. That condition would intermittently...
Hi
i buy a nrf51822-02 module and the chip of this,is nrf51822qfaah10
i compile the ble_app_uart_s130 and program my module but it does not have any advertising
my nrfgostudio...
Hello!
Does anyone know how can we send the multiple uint8_t MOSI signal to SPI and received the result on m_rx_buf?
Trying to send multiple bytes to "m_tx_buf":
...
Hi,
It is possible to use an non secure DFU in SDK 12?Like on SDK11?
How to migrate my custom DFU on SDK 11 to SDK 12?
UPDATE 1
it the dfu from sdk 11 I Get an...
