I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Hello,
are there any plans / work in progress to support 802.15.4 radio in mbedOS?
Currently nRF52840-DK is a supported target platform but if you want to work with
...
Hi all,
I am using power profiler kit to measure as mentioned below screenshot.
I want to achieve current number as mentioned in Nordic product specification as" IOFF_RAMOFF_RESET...
Hi,
I'm using nRF52832 with IAR and SDK V15, S132.
I incorporated the peer manager in the uart serial profile example.
I assume, since I have 3 pages (inc. GC) set in...
I have a device that uses peer manager to pair using a key. I have noticed that the device will connect to an app and stay connected even if the pairing procedure is not completed...
Hello,
I am using the nRF51 dongle, SDK v10 and s310.
I want to use the dongle as a ANT+ receiver and BLE client to connect to multiple BLE peripherals. I have looked...
I am once again frustrated with nRF5 API's. Getting a value from analog input pin is that simple with Arduino API's:
int sensorValue = analogRead(A0);
That's all you...
I'm using an IMU sensor and transferring data over Bluetooth to Android device. The data sampling at 400hz, and I'm sending 6 packets per connection, each packet 20bytes....
Hello!
I am using the PORT event interupt sense handler to wake up the device from various pin interupts. We have in total 6 pins that need to do that.
This works fine...
Hi,
In my project, I am interfacing various modules (UART over ble, ADC, SPI, I2C) on nRF52840-Preview-DK board. I use IAR Embedded Workbench with nRF5_SDK_15.2 for code...
Need assistance/recommendations for working with smaller pin pitch (150 micron) mounting holes for the new nRF52480 chipset. Our current contract manufacturing supplier for...
Hello I noticed the problem with nRF51 DK and ble_uart app.
1. The nRF51 DK is connected to the Terminal
2. Connect to the nRF via "nRF Connect" application on Android...
Hello:
I read the documentation and errata for Rev 1 of the nrf52. I am using the Rigado BMD300 module (thus the nrf52) without a softdevice attempting to do on the fly...
Hi All,
Currently i am working on nrf51822 chip, For that i have downloaded nRF5_SDK_15.0.0_a53641a.
Now, i am trying to execute mouse hid example in nrf51822 chip, but...
Hello, it seems that the 15.2 infocenter radio_test instructions are somewhat different from the 15.0 infocenter instructions . Trying to get a general understanding of how...
Hi there,
I was hoping you guys could point me in the right direction with regards to the use of the nrf_mesh_disable() & nrf_mesh_enable() functions. Since the "friend...
