Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi all, is it possible to use NRF51-DK for Master Control Panel?
I dont have NRF51 dongle so I was thinking if there is a way to make NRF51-DK work with MCP.
Hi,
I have the following situation:
1 central connects and bonds to 2 peripherals. All the above 3 devices are power cycled.
Now, the central need to remember the...
My system's data rate is 16MHz.it input to nRF52832 is parallel 8 bits. Is it possible? I want input the data to RAM by easyDMA,please to tell me how to do it ? thanks!
Hello,
A stupid newbie question: APP_UART_FIFO_INIT seems to get stuck while trying to run
example code.
Only modification I have made is the usage of SEGGER_RTT for...
I am working in sdk14 nrf52832 ble_app_hids_keyboard_pca10040_s132.
I set the .allow_repairing flag to true :
static void pm_evt_handler(pm_evt_t
const * p_evt) {...
My system's extend IC need a 16MHz clock ,because the nRF52832 work in 64MHz,so I want to use nRF52832 to generating a 16MHz clock output to a GPIO pin .please tell me ,how...
Hi,
I'm using nRF52832 and nRF52840 to work with MCU, then we should do the firmware update by the uart. I have compiled the bootloader_secure_serial project in the SDK...
I have ordered two "nRF51822 Bluetooth Smart Beacon Kit"s on this page:
www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit , and got these two:
I've downloaded...
Am building a HID Mouse device, starting with the nRF52-DK as hardware target and the BLE peripheral HID mouse sample app. Builds, loads and runs, apparently fine (i.e., can...
Hello,
I am trying to add an extra service like "experimental_ble_app_blinky" into "ble_app_hids_keyboard" example code. "ble_app_hids_keyboard" example code has 3 servcies...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
i am using uart of nrf52832. the SDK is nRF5_SDK_12.3.0_d7731ad. the uart is app_uart .when i was testing the uart sending and receing .i find that the uart is stoping where...
Hello!
We are performing certification testing for our product. We have nRF52832 chip on the board. We used "radio test" example to perform the test and almost all worked...
I'm migrating from sdk13 to sdk14 with work app.
Can't solve one weird problem. When my app start first time I initialize some data with saving by fds library to flash. There...
