Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,all.
I am using nRF52832.
Does the nRF52832 support dual mode that allows simultaneous advertising and scanning?
Are there any examples you can refer to if you...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
I've been using the nRF52832 chip for over a year and it works great. However, for a new project I designed a board so that the nRF52 chip was the slave on a SPI bus, and...
Hi,
I just try DFU function in sd130/sdk12.3 and it does work very well.
I did:
(1).Generating your own key:
nrfutil.exe keys generate priv.pem
(2).Display a public...
In the example code, I found this:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
I'm having 2 boards (maybe extremely problematic) and I want to...
I have seen at least one person here who has gotten Nordic's UART-over-BLE example app running on the nRF8001. How was that done? Where is it? This example app is not included...
Screenshot of what I'm doing:
So I reset the nRF8001, then try to initiate a transfer by pulling REQN low. However, nRF8001 never responds by pulling RDYN low. I have...
I'm using nRF5DK PCA10040.
And, working on nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I need to enable both of Bluetooth mesh stack and BLE stack.
mesh stack for mesh communication...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
