I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
Example project: blinky_FreeRTOS_pca10028.uvprojx
I include SEGGER_RTT.h file.
After execute vTaskStartScheduler() function.
SEGGER_RTT_printf(0, "Hello World from SEGGER...
Using C11 compiler, and a Makefile from a template, where the Makefile defines CFLAGS with -Werror I get:
.../components/libraries/util/app_error.c:47:5: error: narrowing...
I running the (nrf52) HRM profile with FreeRTOs and connecting the BLE device with the Nordic Toolkit app.
On occasion the connection to the BLE device fails. After repeated...
Hi, I want to interface BLE module with freeRTOS. Does nordic provide BLE stack for freeRTOS? and if yes then is it opensource? or is there any standard BLE stack which can...
Hello,
I want to design PCB antenna for nRF52832 chip. I took reference from nRF51 dongle hardware layout.
I wanted to spread antenna upto 18mm width so I reduced the...
Hi
The j-link detects the chip, but for not obvious reason the j-link and keil will trough an error when I want to program the chip, here is the j-link out put. do you have...
Dear All,
I would like to order Li-Po batteries for my nRF52840 development kits and need some information. From the battery, what type of female battery connector is needed...
Hi, I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
