Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
After configuring and enabling COMP, when READY event emits, is the RESULT register valid? Rephrasing the question: must you trigger the SAMPLE task to ensure RESULT register...
Hi, I've rebuilt so far with the help of multilink examples, the uart example that I can connect to two devices (According to the status of connection-led and the debug info...
SDK:15.2 KeilC:525 SoftDevices:s140_nrf52_6.1.0_softdevice Hardware revisions: PCA10056
I have try the multiperipheral in 4 smart phone connection in blinky App. But I need...
Using nrf52832, SDK12.30 demo project ble_app_uart, testing with nRFconnect app.
Load ble_app_uart demo to board and run. Open nRFconnect on smartphone scan, and connect...
Hello,
I am encountering a small problem with my timer, I followed the tutorial : devzone.nordicsemi.com/.../application-timer-tutorial
The purpose of my project is to...
We have been using SDKv11.0.0 with S130 softdevice on nRF51822-QFAA rev 2 on a custom board with no problems at all.
Since our nRF51822 BLE module vendor no longer support...
Hi guys,
I flashed the mbr hex file and then the open bootloader to a custom nrf52840 board. When i first connect it, it boots into the bootloader mode and i am able to...
Hi,
I need to use
p_status->action == RELEASE_ACTION
to set the brightness level, but the p_status->action only gets updated after the loop finish so:
if (p_status...
Using the Border Router Quick Start Guide I've created the following setup.
2 Raspberry Pis, each with their own nRF5280-DK running RaspPi_OT_Border_Router_Demo_2.0.0...
Hello,
I am using nrf52840 with OpenThread stack. While I am using FDS to store application data, it seems the OpenThread dataset is written in the same area. Thus, the...
Hi to all. We develop new battery sensor based on nRF52832.
We already have an experience with Li SOCL batteries ER14505-VB 3.6V, and satisfied with it. Have in stock also...
I use sdk15.2. bootloader nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_ble_debug. Application nRF5_SDK_15.2.0_9412b96\examples\ble_peripheral\ble_app_buttonless_dfu...
Hello, I'm currently attempting to display a screen during an OTA-DFU process. First and foremost, through BLE, a BLE Central will command my BLE Peripheral to commence DFU...
I am working with NRF52832 master with TWI slave device, however , since our board already has external pull-up resistors (10K) , how do I disable TWI internal pull up resistors...
Hi nordic
I am using SDK 14.2.0 Softdevice s332 5.0 Board nrf52840.
I am doing test about DFU example and I am writing in flash about test image.
It is possible. I made...
