I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
hi all!
I would like to ask the DCDC and LDO two modes of choice. My product is a watch, it uses the cr2032 battery dropped to 2.5v by an external LDO to 52832 power supply...
Hi,
I am using nRF52832 development kit PCA10040 V1.2.1 2017:38. I am able to successfully run nRF_Examples\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral...
hi,
I am using PCA10040 v0.9.0 Nrf 51 DK.
In schematic I am not getting connection for programming connectio n .In sheet 4 of 5 at the USB Connector connection signal...
Hi,
I m trying to develop an linux-application running on node.js to communicate with a nrf52 device. I m using the noble-module ( noble ) and a usb bluetooth-dongle. ...
Hi,
Is it possible to connect nRF905 to nRF51822 via SPI, add ShockBurst code nRF51822 and then use alternately/simultaneously Sub GHz and Bluetooth communication?
I'm...
Is there nRF Connect or similar program that enables development of BLE applications for Windows 10 (using native BLE API - ideally universal windows platform)?
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
I am using the "Nordic Uart Service", example to create a simple serial console which allows a user to change settings such as tx power, advertising intervals so that different...
As in the circuit diagram attached where the pin resource is insufficient For one Pin (AMULTI), I design gpio for Button and analog input as 2channel. (This switch uses the...
Hi DevZone,
I am going to apply a Arduino CAN bus shield onto nrf528400 preview DK. I was integrated this shield with Arduino board and a 3rd party BLE module. Now, I am...
