Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am working on a system where two nRF51 will communicate with use of the ANT protocol (S210). The master and slave must be paired after pressing a button on both sides. I...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
I want to power the dongle from a 5V battery but don't want to solder directly to USB pads at the risk of ruining them. Can I put the 5V from the battery at the Vin point...
I have S110 peripheral device with custom UUID, created as described in www.nordicsemi.com/.../80193304 .
On the other side i have S130 device who successfuly scans and connects...
Sorry for the non-tech. question but I just heard that BlueTooth group is significantly changing BLE licensing policy. Maybe it's some kind of FUD but it should be mandatory...
Hello,
I am running the s110_nrf51822_7.0.0_softdevice.hex and am encountering an nrf callback assert on line 1377 of rem.c.
Without any visibility into this code I...
Hello, before you say anything: "yes I have searched!" :D
I found that this question was similar to mine
How to write GPIOTE Interrupt
Now I am fairly certain that I...
Hello,
I am trying to connect to one specific device. To make this I am advertising with the whitelist. The problem is that the whitelist do not seem to work. I got the...
I am using the nRF51822 module. I am using the following code to set my device discoverable:
ble_gap_adv_params_t adv_params;
ble_gap_addr_t *whitelist_addr[1];
...
I've got a custom board with an nrf51822 (ic rev 2, QFAA), and I'm trying to understand some unexpected current draw that I'm seeing from the board. Currently the entire custom...
Hey there,
Red Bear Labs sells a board with a NRF51822 Module on it. From a past post I have found it is said:
"embedXcode supports the nRF51822 MDK board for both the...
I am playing with S130 to behave as a peripheral device and a central observer. This is working great.
I am new to the central side of things and have a quick question...
