I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Sir,
I am working in nRF52832 board with pca10036. I want to know whether the board supports a loopback control in SPI mode. I need to try for transmitting and receiving...
Hello,
I'm trying to use NFC module on nrf52382 chip (DK PCA10040) and prepared firmware "nfc_text_record_pca10040" from examples of SDK v13. After flashing the Mifare ultralight...
Hi,
In the nrf52.h, SPIM_RXD_Type is defined as below.
typedef struct {
__IO uint32_t PTR;/*!< Data pointer */
__IO uint32_t MAXCNT;/*!< Maximum number of bytes...
i am working with Nrf52 + Visualgdb complier.
nrf_drv_gpiote.h contains designated initializers which aren't supported by C++. I'm including all SDK headers inside an extern...
Hi,
I would like read a long characteristic.
I know that I have to use sd_ble_gattc_read and I have to multiple call this function.
But I don't know where I have to call...
Hello,
I want to implement some kind of control point. This means, that I want to handle BLE write events to some characteristic. I've seen that the payload of the ATT...
Hi,
i tried to find an example with SPI which describes the connection between two nrf24LE1, one as master and one as slave, but i could not find anything. I need the following...
Trying the ATT_MTU Thourughput Example with SoftDevice:
nRF5_SDK_13.0.0-1.alpha_055eef3/components/softdevice/s140/hex/s140_nrf52840_5.0.0-1.alpha_softdevice.hex
on...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
I'm interested in adopting nRF52840 as a mesh networking + Beacon device. It is my understanding that the Nordic SDK for mesh will only be released after Bluetooth SIG releases...
hello everyone:
I work IPv6 over BLE example on both Raspberry pi ,this pic is 6LN (CoAP Server)sending IPv6 over BLE packets to 6LBR(CoAP client) and I use tcpdump to...
Hi,
I'm testing the multi-link functionality.
I want to manage the connections with connection handler.
But, p_gap_evt->conn_handle passed thru on_ble_evt(); and p_ble_nus_evt...
Is it possible to setup the nrf52 with the HRS profile along with UART. I'd like to send heart rate date along with UART messages.
I'd also like to have an android app...
