Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello,
Is it possible to set the clock source for a timer to the RC oscillator?
I'm using Bluetooth in combination with my timer and I see that it is counting differently...
(Windows10, Android Studio 4.0.1, SDK 15.2.0, nRF52832 dev board, App run on Galaxy S10, latest Android version).
Hi, I'm looking to use the Toolbox to create a template...
Hello,
I am having a few issues with getting the SD card FATFS example code to share the same bus as another slave I transfer data to.
I have a few questions:
1) Since...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v14.2, SES 4.52.
The board was running fine for a couple of days.
Suddenly when I reflashed...
Hi,
I started coding form ble_app_uart, and whenever I set a breakpoint and it's caught, then I press Resume (eclipse), the code falls on NRF_BREAKPOINT_COND in app_error_fault_handler...
Hi
My English is not very good, but I encountered a problem that could not be solved. Please forgive me if there is any improper expression in grammar.
When SPI sending...
1.Development board used is nrf9160DK，sim car is nb-lot,set's network mode is nb mode，Turn off all peripherals
2.set eDRX mode,eDRX is 655.36s,pwt is 2.56s ,After the device...
I am using the GPIOTE driver to attach interrupts to a pin in a very timing critical environment (using sensors like this ).
To me, it seems like there is quite the significant...
In the v16.0.0 SDK the settings struct size is 904 bytes, but in the nrfutil it's 803 (screenshots attached). I figured the settings in python don't include peer_data(64bytes...
I was in the process of integrating a NAND flash to my project. - MX35LFxGE4AB
Initially, I thought it would be good idea to use QSPI, but it seems to only support NOR flash...
Hi
Im struggling to use the ble_app_template_cpp within SDKv16. I am using the nrf52840 DK (PCA10056) and want to us the S140 SoftDevice. The example isn't built for either...
Hello everyone:
The problem is still not resolved
Test broad is PCA10056
Test code was modified by \SDK17.0\examples\peripheral\usbd_msc\pca10056\blank\ses
Try to...
I am using a thingy52 device and in that, added code of advertising and scanning from the sdk 16. Advertising is run successfully. But getting packet loss issue. So, I am...
Hi
Im developing an application that will wake up on RTC every 15 minutes. My issue is that when using idle_state_handle, which in turn calls sd_ble_app_wait, the RTC...
