I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
trying to get nrfutil working on ubuntu, following this guide:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html
after...
hi, I have used to segger j link basic with nrf connect programmer to program mass production.
but, It takes 30 seconds. For better efficiency, can It be improved to change...
Hi Everyone,
I need to develop a bootloader and a firmware update procedure.
My development environment is nRF52840, sdk 15.3.
Program download configuration 1) Download...
Using Mesh SDK 3.2.0.
The returned Device Composition Data is malformed when requesting it after the node has been reset. This is because the sig_model_count and vendor_model_count...
Hi to all,
i am trying to develop an app with NRF52840 soc and nordic sdk 15.03. in my app i implemented a usb hid device and also i am using flash storage at same time...
Hi
After getting SDK16 , we have tried to load a combined hex file with bootloader + S132 V7 + application with dfu + bootloader setting page to PCA10040. And It work well...
Hi,
i am working with aws-fota example, i copied my certificate to certificate.h file, once i run the program it shows like
The MQTT AWS Jobs FOTA Sample nrf_inbuilt_key_delete...
Hello, I started to delvelop an program from mqtt simple, now that I almost finished I saw that mqtt is refusing to connect to my broker, I deleted all my code I wrote and...
hi ,,, nrf52832 , at first for bonding i will connect my device manually by scanning and after passing the data to flash , i will disconnect . in program i have set the timer...
I'm writing test code to verify the softdevice operation according to the spec.
The goes like this:
The central sends the feature exchange command, when the feature exchange...
Hello,
I have been experiencing corruption using a similar implementation to the USBD_MSC example. Even after the various SDK fixes suggested to the same problem outlined...
Hi Øyvind
I can't programing the target board.can you tell me On the "debugger" nrf9160DK ,What do I need to set?
I followed the Settings below:
On the "debugger" nrf9160DK...
Hi,
I am trying to setup a ble sniffer to make sure another one of my devices is sending the correct data to the central. But the nRF sniffer does not seem to be picking...
We are using a custom board with an nRf9160, and have tested it with several sim cards. The board has been tested with a spectrum analyzer and it is able to transmit RF, however...
