I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am trying to implement capacitive touch with nrf52832.In our application we require three events to be generated.
1)On holding for 3sec(Device Turn ON)
2)On holding...
Hello Nordic Pros,
I haven't been able to chase this one down on my own, so any help is greatly appreciated...
We are developing a product and app that connect to either...
Hello,
I'm using the rigado BMD350 in a new device with the legacy BMDware (AE firmware).
I'm have enabled the uart service and i'm debugging the transmission using the...
Hello,
I am trying to use the CLI example, but when I compile and upload it, LED1 does not blink and I do not get anything back on the serial port.
There is no error during...
Hi,
According to the data sheet, nrf52840 supports XIP mode on QSPI flash. Can we configure I2S(easyDMA) to load the tone from external flash with XIP address and play it...
I use a motion sensor interrupt and 4 buttons and one charge interrupt, all works well in product development, but after go into mass production, some pcs product( 1 or 2...
On the previous nRF51822 project the SWDIO pin could be used for nRESET.
The nRF52832 Product Specification and example code program nRESET to P0.21.
The Product Spec...
Hi,
One of my customers examine the feasibility of using nRF52832 as Peripheral only ,his mandatory request is Security because the product is an electronic lock.
Please...
I use nrf51822 to do bluetooth keyboard, I hope the function is: I want to change the IRK value of the bluetooth keyboard each time it is paired and bound,Anybody know how...
Hi can somebody help why nrf52840 doesnt be reseted when you press SW5(if boot/reset)? I have alredy with tried with few examples flashed on nrf52840 and in Segger IDE set...
Problem :
I have two I2C devices and would like to connect them both to nRF52840 DK on different I2C pins. According to datasheet nRF52840 has two I2C pins (P1.00, P0.22...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Hi,
I am trying to build out a button pressing scheme for BSP on a custom device with 15 buttons operating on a BL652 Laird Module (underlying nRF52832). After modifying...
I'm working with the NRF9160 DK and have found the sample times for the ADC to be abnormally long. I am sampling three channels and seeing a total time for the ADC read of...
Hey guys, I am using 2 nRF52832 boards with a PCA10040. I program my boards with the BLE UART central and peripheral examples. I was wondering if it is possible to, and if...
