Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi, everyone. We are developing BLE project on the chip nrf52832 with SDK 15.0.0 software. In this project we are using ppi feature. During the work the program must enable...
I am trying add the fatfs example in my custom solution and I have the follow error after add the paths and files.
nrf_log_frontend.c:92:35: error: unknown type name 'nrf_log_module_dynamic_data_t...
Hi,
I am working for Adafruit on the bootloader for the upcoming feather nRF52840. Currently testing using the nrf52840DK pc10056. Everything is OK with S140 6.0.0 . Today...
I need to implement a 4kHz signal to drive a buzzer on a custom board of nRF51822 with external 16MHz and 32kHz crystal.
I am using Timer1+PPI+GPIOTE to generate this 4kHz...
I'm currently using:
- Board: NRF52840
- SDK for Mesh 2.1.1
- SDK for Thread and Zigbee v1.0.0
My problem is that I want to merge and run both Bluetooth Low Energy...
Hi, I am using nRF SDK 12.0.0_12f24da, with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c
Initially I was working on integrating...
Hi, I am using nRF52840-DK; Window 10; Embedded Studio and try to run sample project:C:\Nordic_Semi\nRF5_SDK_15.0.0_a53641a\examples\peripheral\ uart \pca10056\blank\ses ...
Hi all, I'm using nrf52832 with SDK15 in my project. For debugging purposes I need both CLI and LOG modules enabled with RTT as a transport. I followed this manual to setup...
How can I disable NRFX_LOG_INFO calls in the PPI driver? I've set NRFX_PPI_CONFIG_LOG_ENABLED 0 and even NRFX_PPI_CONFIG_LOG_LEVEL 0 but that doesn't stop messages like the...
Hi,
This is Srivisakh. I am using a custom made board integrated with nrf52832 board in which UART is configured. I am using Segger IDE for code development and building...
Hello I have what I hope is a simple question regarding the Internal DC/DC on the nRF52832 and thus nRF52810. I am assuming it is the same internal design, correct between...
We are just in the very beginning of developing a mesh network with 150 devices and a gateway (with a nRF52840 in it). We want to find the best strategy for provisioning....
Hi everyone,
thanks for this discussion - this question addresses almost exactly a potential use case I've been looking into.
I'd like to try and implement something this...
This is from the documentation:
[in,out]
p_length
Pointer Length of the string. Amount of sent bytes.
I'd translate it to a pointer to the requested length...