The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Is there any way to detect / prevent the use of range extenders?
When using a central & server with low TX power, the range is say 10m.
Now an attacker can use a relay...
Hi all,
I have been using Nordic chip-sets for a while mainly for BLE applications. I am now developing a simple lighting product based on Nordic nrf51 family chip-set where...
hello!
i am working with the component nrf52840 v0.5.1 and i need development a thermal profile according with the datasheet of the component nrf52840 v0.5.1
could you...
I'm using op-amp(LM358), condenser microphone and PCA 10028.
My project collect output values of op-amp and broadcast that.
But, noise was occurred while it is advertising...
I'm using the ble_app_multilink_central example app.
In the pca10400.h I changed #define BUTTON_PULL to NRF_GPIO_PIN_PULLDOWN.
The problem is that the first pin interrupt...
Hi
I'm creating an android app for smartwatch(used nrf51 ble),I have two questions
1.I used ANCS(Apple notification center service) in my android app,but nrf51 device...
I'm using the SD (nrf52) MBR to update our custom bootloader, in a battery powered device.We have some custom hardware which is used to disable our LDO, to enter a "Ultra...
Hi Everyone,
Recently I have been trying to measure the current consumption from the dev board.
I have set up the board as instructed by cutting SB9 and soldering SB11...
Hi,
I see intermittent incorrect values from the saadc. The code is described here .
The graf shows battery voltage in mV over about 4 days with one sample per minute...
I am getting following errors when compiling source code in Keil-5. Any one suggest me what i am missing to define symbol?
linking...
._build\nrf51422_xxac.axf: Error...
Hi,
We have devloped PCB based on nrf52832 as beacon.
We have also developed firmware for that and it will advertise for some and than go to sleep mode and after some...
Hi,
What is the minimum number of symbols in preamble nRF52840 has to receive in order to receive full packet on Coded PHY? I can see that it can easily receive packet...
help! Thanks
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
chip:nRF52832
we found that the pstorage's callback will not be triggered when the Bluetooth...
Hello,
Issue : XOSC16M is not Starting and the loop stuck forever in below line
while(!pwr_clk_mgmt_is_cclk_src_xosc16m());
where it checks CLKLFCTRL 's 3rd bit...
