The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nrf51822 TWI library. I've tried both twi hardware and software master library files and see the same behavior when using both (as a side note an explanation...
Am I right in thinking that the button handler only causes an event for a button press(although I realize it is possible to configure the button such that a release is interpreted...
Hi,
I have a Question regarding one project in which 1 NRF24L01+ Module transmit to multiple devices at the same time ? How we can configure for multi transmit ? like Tranmitting...
Dear Nordic,
The guys at ARM have this community around mbed which looks great. I would like to use it, but before I do, I would like to check if their use of your (source...
Hello,
I'm trying to understand how the ble_app_hids_keyboard example works. So far, I have hooked up a few more buttons to the board and can type hello.
Now, I would...
Hi all,
In my project I'd like to use gazell for to communicate 2-6 devices with host.
Furthermore I use switching between BLE and Gazell (only 1 device support till now...
I am trying to port an application from MBED LPC1768 to a nRF51822 Evaluation board to develop a multi-function application for the nRF51822. The BLE part (developed on the...
I am hoping to develop a device that works as a remote control for a smart phone app. There will be at least 5 buttons, and as the button presses will be infrequent, I am...
Hi
How to start and stop scanning continuously in android devices ?.I found that In Nrf master control panel android app there is an option of performing scanning such...
Hi,
I downloaded and installed latest master control panel for Win7. It now crashes when communicating with nrf51 dongle. Seemed like it crashed the first time while it...
I'm using the APP_BUTTON_INIT-Function to register a button at the GPIOTE-System. This works great while running normally, e.g. I can react on debounced button_down or button_release...
Hi
I am developing for the nRF51822 a 4 layer print with a power and a ground plane in the inner layers. I will be using a balun from Johanson Technology (2450BM14E0003...
I've heard that's not allowed. If so, why?
If it is allowed, are there any precautionary steps I need to take, not to interfere with the radio?
Thank you!
Gil
...
Hello, we have a custom board based on the CEAA WLCSP reference schematic with internal LDO setup. Our supply voltage is 1.8V (VCC_nRF). Unfortunately we don't see any BLE...
