I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I'm using the S110 v7 SD, I want to amend the bootloader app such that I can merge it with my APP together with the SD to a single .HEX... To do so I'm taught to init. the...
Noticed that the WLCSP packages are being offered with a "build code D0". What does the D0 signify ? Any implications to programming the chip?
www.semiconductorstore.com...
I have tried to merge the hex files using mergehex, and flashed it to my device.
After flash the device is in DFU mode.
It seems the booloader doesn't know that there...
Could someone please explain or point me to rules for creation of such type for custom service?
I did look at provided examples but there are no comments telling why members...
I have a vendor specific characteristic for the battery voltage in my device, expressed as an actual voltage rather than a percentage. Values are 0.000V to about 4.300V and...
HI,all!
I recently using pstorage to store data
and the pstorage_store(); funtion always returns NRF_SUCCESS, but never triggle the cb_handler, is that normal?
by...
[environment: s110_nRF51822_7.0.0 + SDK nrf51_sdk_v6_0_0_43681 + PCA10000(QF AAG0)]
I failed to get pstorage working in my own code, then I picked up the sample code from...
My NRF51822 die. When connected, keil can't download or erase flash. But it can be found by SW port when I just power on, then it almost be unavailable at the same time. ...
Hi,
I am trying to use the RX interrupt on the PCA10001 board, using UART0 for wired communication and S110 (s110_nrf51822_5.2.1) for Bluetooth LE communication at the...
Hi, i'm trying to communicate between a msp-430f5529 (spi master) and a nrf51822 (spi slave). I have configured the MISO, MOSI, CS and SCLK of the nrf. I use the spi_slave_example...
Hi there,
I'm currently facing the problem, that an example as simple as
volatile float sum;
extern "C" int _start()
{
float a = 1.0;
double d = 2.2;
sum = a ...
I have a nRF51822 mkit board which I would like to use as a BLE peripheral to connect to my linux computer with BlueZ. I would like to be able to have a simple GATT connection...
Hi,
I'm trying to get a SPI based peripheral going without much luck.
One thing I noticed, in the debugger, is that on my implementation the field spi_base_address->POWER...
Hi,
I'm getting problems on the pca10001 uart example. I get the "Start:" string on the terminal but it can't echo what I type on the keyboard. Another thing is that I...
