Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Nordic support,
I am building the ble_connectivity project of the latest SDK11. My EVB is pca10028m, the project is located under "nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral...
HI,ALL,
in the Blue Core Spec, there are such statement here,
L2CAP permits higher level protocols and applications to transmit and receive
upper layer data packets...
Hi, I use [nRF5_SDK_11.0.0\examples\ble_peripheral\ble_app_hrs\pca10040\s132],but I get error such as the following.
{
............\components\softdevice\s132\headers...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
HI, I am new to embedded system and just start to learn NRF52 DK. currently I want to configure a pin of nrf52 as interrupt. so i created new GPIOTE_Handler function . however...
hi, i am getting a lot of help in here, thanks a lot
i'm using SDK 6.0.0 for my project. and i want to use timer as a counter like as the title.
then, i fount the app_timer_cnt_get...
hello,
I am using S130 softdevice. While I am trying to connect with MCP I am getting one error with error code :0x08. and MCP is showing a message like "Lost connection...
Hi,
I have a battery powered device which goes to system off mode when it is not used. I want to do some stuff when the battery is inserted the very first time after production...
My application uses the Softdevice, app_timer and app_pwm.
So all timers are in use, but I have to measure two more pwm signals on two input pins.
(Those come from HC-SR04...
Hi,
I'm resetting the chip externally using the reset pin to not be in debug mode. I'm running the system off example here modified to not use buttons.
I have the J...
Hi,
I am looking for some assistance to choose the best way using the nrf52832 processor in a correct way.
The main task is to generate a 1KHz PWM Signal with changeable...
Hello,
I am using nrf51822 ceaa package.
What would happen if dec1 pin is not connected to a capacitor?
According to the datasheet, it is for power decoupling and...
I'm developing py script for automation testing of nRF devices.
My script is based Nordic's scripts Master Control Panel\3.7.1.8567\lib\dfu...
So, during testing my script...
Hello,
I have some devices based on NRF51822 using ESB lib and developed with Nrf51 SDK v10 (no softdevice). Since Nrf5 SDK v11 is released, the new device will be developed...
Hi,
I am curious about how the connection is keep while using the 32.768K in BLE link layer in power saving mode.
I know that the connection interval is based on multiple...
