Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi
I try to program Insight ISP 130301 with a hex file, which works on nrf51 PCA10028. Unfortunately, it doesn't work. I try to loop for each pins and set it's state, and...
I'm trying cominicar me through Termite between the application plate (nRF51-Dk kit) and a device that supports BLE, but the connection between PC and the kit application...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Hi again, I posted earlier in another post that my writeCharacteristic is responding with status 6.
Details:
Android version: 5.1
Nordic device: nRf51822 S110
I have...
Hi
I want to use nrf52 LATCH register.
I can see the correct bit set in the register, but I am unable to clear this bit.
I have tried NRF_P0->LATCH =0xFFFFFFFF; for my...
Hello
I am doing a PCB design using nRF51422-QFAC chip. I did based on nRF51-DK but now I would like to change for a SMD antenna (2450AT18A100 from Johanson Tech.) instead...
Hi ,
I am working on one application in which i need to stream the ADC values over BLE to the mobile App. This should happen at very high rate i.e. 1000 samples per seconds...
Hello,
I'm trying to do something like ibeacon where data is pushed to any device listening, but I want to update the advertising data from raspberry pi 3 since it supports...
Hello,
I am working on an application where the nRF51 acts as both central and peripheral. The device is in permanent connection as peripheral while scanning for other devices...
Hi
can ESB be considered RealTime transfer as soon as it has it's timeslot?
Outline of use-case:
Device advertises existenace on BLE
If there is data waiting...
I am trying to implement a REQ line protocol over GPIO to signal to the Master when it is ok to receive data. Basically, I want to pull the REQ line high when the nrf51 has...
Hello,
Ble spec says that "new alert" characteristic - field: "category ID" can have 1 or 2 bytes.
here
But it seems in your struct you let it have only 1B.
typedef...
Hi,
I have ordered a PCB using the reference schematic for NRF51422 user guide.
I wanted to know whether the schematic has the required antenna design or I need to add...
Hi All,
I have a basic question about advertsing data, more precisely about device's address.
I try to disable in my advertising data, the address field but it doesn't...
