I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi,
Next problem I've experienced is jumping processor to Hardfault state at sd_ble_gap_adv_start
with whitelist and BLE_GAP_ADV_FP_FILTER_CONNREQ .
In case adv_params...
Hi
Although I followed and got working eclipse Mars on win10 using this great @Vidar tutorial I am still having problem creating a new project under eclipse for any of...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I am developing a power aware TWI driver for 51822/422. All appears to work properly except when I simulate a bus fault by shorting SCL to ground or shorting SCL and SDA together...
Hi,
Firstly a warning I'm a noob in this area.
I'm seeing some strange events consistently returned from the nRF8001 over SPI. I have an example of the SPI traffic below...
Hi! I would like to get adc sample from two different channels at the same time on my beacon (nrf1822), using the same interrupt. Is that possible?I mean I can use ADC_IRQhandler...
Hi,
It's a very simple question, is there a simple way to check GPIO pin status. I just want to know at a given time if the Pin is High/Low. I don't think I need an ISR...
Hi, I just started working on nRF52 with Bluetooth, and I have some concerns about DFU and security.
I’m working on a product equipped with an nRF52 and a MEMS microphone...
Hi!
I am using the NUS service and I noticed that Android 6 (Marshmallow) will not go faster that 47.5 ms. Even iOS can go to 30ms. My target is 7.5.
Am I doing something...
Hello,
I am using nRF52832 with S132 and SDK_11.0.0. I am facing issue with using power fail warning POFWARN. below is my code snap.
void POWER_CLOCK_IRQHandler(void...
Hi All.
I'd like to know how to turn off or on shockburst feature.
After I set auto ack & retry count, Tx successful interrupt occurs, even though receiver device is in...
I'm migrating an app from SDK8 to SDK11 and I'm getting errors using TWI to communicate with my IMU (Invensense 9250). I first tried it on a nRF52 DK (Eng B) and then went...
I've either got a bug in my code or the JLINK connection is dying. Either way it's a real headache to pinpoint and discover how to resolve. Knowing more about extracting info...
Hi, Now I use the NRF51822 ADC to sample VCC , 1.2V internal reference，internal prescaling 1/3.The PCB connection show as the pictrue .My application develop base on soft...
