I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
I'm having some issues getting the auto ACK to work properly. I am only receiving auto ACK messages on the first 3 received packages, after which the receiver stops replying...
Hello i have a system that build in an ultrasonic sensor RedBearLab BLE Shield ( nrf8001 ) and arduino i want to get ultrasonic data via bluetooth and see it on nRFConnect...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
I am trying to develop a GATT service on nRF51.
The GATT service measures a few values, and stores them in a characteristic. When the GATT server (phone) requests data...
I am trying to build a device to stream the 9 axis sensor data from the I2C based sensor and then transmit it using BLE UART profile. It is sampled every 3 seconds using app...
I am using an nrf51422 board. I want to update via OTA using ANT+ Dongle. The device information shown in the OTA Updater is parsed from the Bootloader Code. Is there any...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello all
I am trying to implement hardware flow control for UART.
is there anything else to be done ? I have done the GPIO configurations like this
const app_uart_comm_params_t...
Hi,
I'm trying to migrate from SDK 6.1 to SDK 7.2 on custom board.
In SDK 6.1 everything works fine (SoftDevice v7.1.0), but with SDK 7.2 I get into HardFault Handler...
