I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Device: NRF51-DK
I'm using GDB+OpenOCD to step thru code and it appears that the nrf51 resets itself after calling:
SVCALL(SD_BLE_GAP_ADV_START, uint32_t, sd_ble_gap_adv_start...
I want to make rs485 communication with nRF51822. I gone through the UART code, there CTS , RTS pin are required , but for my case tx, rx,rx enable is enough, and also shall...
Hi everybody!!!
I am making a project which use NUS service and I have confuses in connection mode:
when the central and peripheral do not have data to transfer...
Hello, my question is pretty clear i guess. Is it possible to schedule advertising of 2 different packets on the same chip ?
The way i see it, it should be possible to...
Good morning, I´m trying the example of this post (ble_app_template_with_pstorage_operations_nRF51DK.zip). I have SDK 8.1.0, softdevice 110 and nrf51-dk.
The source works...
Is there any clear documentation to add an external memory to the nrf51822 to store some sensor data. How is the performance and stability when interfaced this way?
Dear all,
I'm working with nrf52832 and SDK 11.0.0.0.
I want to upload SD 2.0.0-7. Download results OK but,
nRFgo Studio, when accessing the unit reports:
Region 0...
I just got the signed bootloader to work with the single bank implementation but had to change dfu_single_bank.c. I believe the change represents a bug in the code.
In...
We are working on a nRF51 device and and corresponding iOS App, and we would like to set the name of the device. The problem is that when connecting with an iPad using BLE...
Hi,
Im trying to use BLE DFU Bootloader from examples. I loaded SD8 and then bootloader via nrfStudio (dont have a valid app flashed), but I cant see the device from Android...
In [sdk10_folder]\components\ble\ble_db_discovery.h , BLE_DB_DISCOVERY_MAX_SRV is given the value 2 .
In [sdk10_folder]\components\ble\common\ble_gatt_db.h , BLE_GATT_DB_MAX_CHARS...
In another thread entitled:
Change in GPIO to start/stop timer and fire interrupt
The following code is used:
NRF_GPIOTE->CONFIG[0] = (GPIOTE_CONFIG_POLARITY_HiToLo...
