hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
In my plan I have a rf moudle NRF24l01 , this is not important, so , If you see in figure 1 we have radio masts that send waves in around. we can't accept this. my plan for...
I have a system where any two identical devices need to establish a communication between each other, without any prior knowledge of which is master and which is slave. Currently...
I have the 51822-DK. I was finally successful in uploading the Heart Rate Monitor example application to the chip with the S110 but now it looks like nothing happens. I downloaded...
Hi nordics.
I am trying to do s120 multilink_central example.
However, this example doesn't work well, and I cannot debug central example.
-Environment-
board...
Hello,
I am working on pca100028 and using s130 softdevice(SDK 6.1.0.0.). I am trying to see UART log on pc. But my code get stuck at the following while loop.
void simple_uart_put...
I am using ATmega32s to drive the nRF24L01+ chips and a low dropout 3.3v regulator (TI’s LP2950) to power the nRF from the five volt buss.
Both the transmitter and receiver...
We are seeing bonding issue between Nexus 6 and our 51822 based product. After inspecting the sniffer capture, we observe that the phone advertises its IO capabilities as...
I have an nrf51822 S110 based application that tries to discover the primary services on the GATT server at every connection of a central.
Unfortunately, the central does...
Hi,
I have read all the answers about ANCS, it seems there is no conclusion can be resolved the problem, that is "It seems working first connection. But after rebooting iOS...
Dears:
I'm using nRF51822 with softdevice S110 . And I want to know, how can I switch the communication mode betwean BLE and 2.4 G ?
If possible, could you provide me...
According to ble specification [1] and based on my test with iOS, the cts_c library seems to have bugs on a process decoding adjust reason data.
Here is a simple diffs...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Hello everyone,
I have a nrf51822 dev board which cannot program because of Keil is giving me errors which I detail here.
I'm using Keil uVision 5.14 and as you can...
In my current design, for the schematic and layout I've copied the design of the first version of the usb-stick with meander-antenna and matching network/balun. In the later...
Hi,
I have been programming PCA10028 using these commands for a while without any problem:
$ JLinkExe -device nrf51822_xxaa -if swd -speed 4000
J-Link>loadbin s110_nrf51822_7...
