HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi!
I have an nRF52832 on a custom board. I managed to flash it through JLink and STLinkv2. But suddenly, I wasn't able to communicate to it anymore.
Openocd tells me...
Hi
The new signed DFU in the SDK12.1 comes along with a experimental buttonless DFU. There are a few bugfixes required to make it working, but the nRF Toolbox app didn...
Hi:
Recently, I want to use nRF52 to read or write some data from a flash chip(w25q128bv) by using spi, I've read Manufactures ID correctly, also, I have wrote a register...
Hello!
I need to interact with two J-Link debuggers, connected to the same PC at the same time. I would then read and write data to the devices connected to the debuggers...
Hi team,
iam using sdk 12.1.0 (ble_app_beacon) I want to advertise the battery percentage.Right now iam using the nrf dongle(it doesn't have cell coin battery) and flashing...
I am attempting to build some ptorotype code using SDK 12.2.0 and GCC and I just added calls to the app_schedukler library and to the saadc driver. I added the relevant source...
I always read 0 first time I call sd_ble_gatts_value_get(), the second time and forward I read correct value. Even if I call sd_ble_gatts_value_get() twice in a row the first...
Hello,
I generated a new project using the main.c of the example "ble_app_uart" from the SKD 12.2 for a nrf52832 and from there copying all necessary .h and .c-files into...
Hi DevZone
I am trying to DFU OTA a PCA10040 using BLE Secure DFU Bootloader from SDK12.2.0.
I can succesfully transfer the image i have made with nrfutil to my DK,...
Hi,
I'm working on integrating ANCS on our existing and futur products. I started to port the Nordic SDK example (12.x) and it seems to work fine on nRF52, which will be...
I am currently using SDK 12.1.0 and experiencing intermittent HardFault crashes in timer_list_remove() with the stack indicating the origin being a SWI0_IRQHandler call. ...
i have a setup with one NRF24L01+ as PTX and one NRF51822 as PRX
my problem is that the data sended ok and ack sended to NRF24L01+(i assume that by NRF_ESB_EVENT_TX_SUCCESS...
the application need the nRF24LE1 to go to memory retention sleep model for more than 2s，and we know that RTC can only timer for 2s.i used WDT to do this job , but there is...
