Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi all,
I have a working prototype of a service which enables a number of characteristics for the control of motors and relays. The motors work great, and are controlled...
Is it possible for gpiote_event_handler interrupt to get executed while the program is executing code inside timer_event_handler?
These events modify same variables so...
I intend to keep a long running clock in the system and use the app_timers(hence RTC1) in a soft device enabled nrf51822 firmware.
I basically have a minute tick and update...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
Where can I find an example of using device manager? The SDK doesn't have anything. I am using S110 7.1.0 and SDK 6.1.0 on nrf51822. I am having lots of problems with iOS...
I try to use Android studio to build nRF Beacon project,but it didn't work ,and there are several error .
the error is
Error:(50, 35) No resource found that matches...
Hallo,
I try to use the s310 timeslot API. I open a "session" and then request a timeslot:
check( sd_radio_session_open( nrf_radio_signal_callback ) );
request_radio_slot...
I am trying to implement the pulse counting mentioned in a previous post of the same name, but the code is eluding me. I am using the heart rate service example with new code...
Hello,
I want to implement a firmware update over ble for my application and the SoftDevice 130. Which would be the correct boatloader.hex that I should use? I am working...
Hi,
I am using softdevice-7 and SDK 6.1 for our application.
If I connect using a passkey, first 「BLE_GAP_EVT_SEC_PARAMS_REQUEST」 event occurs, then the 「BLE_GAP_EVT_PASSKEY_DISPLAY...
I have a mature design with several hundred units built using QFAAE0 silicon. Code works. Hardware works. FCC is happy.
I'm considering migration to V3 silicon and maybe...
Hi....
I have PCA10028 DK and i want to make a profile that works both as central and peripheral. As a part of this i tried running S130 demo app found in S130_softdevice...
I need to remember the CCCD's of some service, e.g. service changed. A CCCD is according to spec 2 bytes long. The method to do this is by using sd_ble_gatts_sys_attr_get...
Not sure why but my time is only firing at 250Hz with the prescaler set to 0. Not sure why. Shouldn't it be going at 16Mhz at these settings? (Running on the PCA10028 Board...
