We are trying to build a box and woiuld like to have external antennas connected to it. Is there a specific product or the name of it so that we can search and compare from...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hello,*
I'm new to nRF Connect SDK environment, but I'm used to work with Zephyr.
I'm actually confused using west.yml file. I created a new application based on existing...
I'm using s110 softdevice 6.1 SDK. I do bonding in my application the same way as in the ble_app_hrs example (bond, no_mitm). I have a charactarestic set to SEC_MODE_SET_ENC_NO_MITM...
my chip is nrf51822,I used s110-sd-v7, it's work. I switched the software to s110-sd-v8, GPIO interrupt is high priority (APP_IRQ_PRIORITY_HIGH). I erase the flash (pstorage_raw_clear...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
For a new product design with the nRF51822-QFAC rev3, could you give me the matching baluns ? Just the Johanson ?
Presently Stmicroelectronics told me that the BALF-NRF01E3...
Hi Sir:
I written below code according to example code.
In timeslot, rng will start with "rng_start_bv ".
Then the process will wait until "rng_ready"==1.
But, it can...
Hi,
I'm trying to implement a pulse counter, and send the data to client via BLE. I have debugged the module of the counter without connection separately, it's working...
The ' Downloads ' tab at www.nordicsemi.com/.../nRF51822-Evaluation-Kit gives only the v2.0 Hardware Files.
I have the older v1.0 board - it isn't quite the same!
Where...
Hi,
I'm having some trouble setting up the vendor UUIDs on a nRF51 devkit. I've written a short application based off of the template example, providing a service called...
Hi
I am using timer1 for generating 4khz input to buzzer.It works fine when no ble starts.When advertising starts buzzer shows some flickers according to advertising time...
hi,
im developing an application with peripheral and central.ive used hrs service its working fine initially bt if you keep it idle after some time the peripheral stops advertising...
I am trying to figure out a way to secure my DFU (via BLE) such that someone cannot sniff the and copy my hex code (and decompile). I cannot use Pairing or Bonding as that...
I can use "Pack Installer" to copy example from Keil folder to my hard disk driver, for instance, I copy ble_app_cts_c to my personal folder.
I can build and flash ble_app_cts_c...
Hello there, I have been trying to look at the documentation and the forum but haven't been able to understand the difference between BLE stack event and SYS event. Could...
Hi,
I have a the nrf51822 chip on a custom board and the ble_hrs code loaded on it. Now I would like this custom board to behave as a beacon with the hrs code sending data...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
