I am implementing sha256 with hash message bigger than or equal to 8KB. I tried with nrf54l15dk_nrf54l15_cpuapp target, and it's working fine but if I try with nrf54l15dk_nrf54l15_cpuapp_ns...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hi,
I am currently evaluating the nRF54L15 dk and porting the old project code from the nRF52DK to the new nRF54L15DK devboard. However, I have encountered an issue with...
Hello,
i would like to use HRM, HID, BAS and DIS profiles simultaniously. I used HID mouse example. I append required HRM things and it work almost properly. Problem is fault...
Hi, I'm a beginner. I want to add to example of the proximity, next service identical to battery service. I need to send 1 byte of data.
Everything works well until when...
I have an application that reads an nRF51822 pin configured as analog input and then sends that value using "ble uart" (included in Nordic's sdk). Analog input is read in...
Been studying the S110 5.x -> 6.0 migration docs. Are there any project-specifics / include-paths / Keil build-settings that must be updated as well?
Do I understand it...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
I have a nRF51822 device which has softdevice and bootloader.
And I'm trying upload my app with following steps:
make .bin file with gcc
Push the DFU button, and...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
I have tried HTS(Health Thremometer Service) sample Program on nRF6310, PCA10006, SEGGER J-Link Lite and iPhone5C.
First time, temperature is displayed on the iPhone5C...
Hi,
I have a custom board with nRF51822 chip on it and tried to run the proximity sample program on it. I have used the nRF51822 develpment board + nRFgo Motherboard to...
www.dropbox.com/.../Screenshot 2014-04-03 11.41.25.png
I guess has nothing to do with crc16?
the call stall seems unreasonable, is it because my stack is messup?
...
Hi,
Is it possible to control the drive current of the gpio pin?
Can anyone explain the different possible drive configuration for gpio's (S0S1,H0S1, etc..)?
Regards...
I'm trying to compile the bootloader for gcc from this post: devzone.nordicsemi.com/.../nrf51822-over-the-air-bootloader-with-gcc
The bootloader start (I can find my device...