Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi:
I use TIMER compare function, I open four channels and every channel produce interrupter.Here are some of my code:
NRF_TIMER1->TASKS_CLEAR = 1;
NRF_TIMER1->CC...
Hi. I've never asked a question here, and I'm a complete beginner to embedded programming, so I apologize if I break protocol in anything I do on here.
My setup:
nrfgo...
HI,all!
I have a question about downloading program into nrf51822 MCU.
That is:
As you konw, using the nRFgoStdio to download the code, you have to download the softdevice...
Hi all,
I have a devicewith display and only want a specific smartphone with my APP to connect to it.
I implement the authentication procedure at application level by...
We have some product using nRF51r22 QFAAC0.
E0 version is replacing C0 now. I just want to know when is Nordic going to stop producing the old version?
Thanks
Hi, I'm a ble developer using nrf51822.
It is a wierd question,
Is this any possible to write value to one characteristic's CCCD value from itself(device)?
This is my...
I am using the nRF51822 Development Kit
I have compiled the blink_example and the s110 ble_app_hrs in the nRF51_SDK_v5.2.0.39364.
I am unable to program the SoftDevice...
Are there any I2C examples for the nRF51822 ( write/ read functions) ?
If not, can anyone suggest a good starting point for I2C?
I am using Eclipse kepler for development...
In the nRF51 SDK examples, some pass the parameter adv_params off the stack as a locally declared vaiable in the context of the function and some pass static global variables...
I successfully made an Arduino code using nordic library that gets notification from iOS ANCS.
But some minor bug exists: sometimes i don't get any notification from the...
Hi all,
I used the ble_app_hids_mouse example in SDK 4.4.1 and found:
1.when the mouse does the first bonding with the master, the report rate could reach 125Hz(I set...
Hi, I am trying to code my nRF51822 on my custom board, however right now I'm having my doubt on using some of the example code provided in the SDK.
Essentially, I want...
Hi,
1/ I download the s110 softdevice and ble_app_hrs to the nRF51822 board, and running normally.
2/ I download the s120 softdevice and ble_app_hrs_c to the nRF51822...
Dir sir. I read the white paper "Tuning the nRF24xx matching network" and I have a question.
I would like to know the setting of the spectrum analyzer when I measure the...
I'm looking at the 5.2 SDK and I have noticed a few minor things that may be bugs or might be my mistake but here goes:
In the GCC linker scripts, I was carefully...
