Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
Hello everyone,
I am a beginner looking to dive into the world of HID (Human Interface Device) development, specifically using the NRF52840 microcontroller. I recently...
One of our products that's been in the market for a couple years is a bit behind on the NCS version (v1.4.2). I am currently doing the 18031 RED Cybersecurity documentation...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
i want to advertise my one device into coded and into another device i want to do coded distance measurement it is possible to do in nrf 52840 version 2.5.1 ?
Helo, I have ISP1907 for BLE AoA.
In my understanding, the antenna spacing should be half of wavelength, in case of BLE, it would be 2.4GHz thus the spacing should be 6...
On a new board based on nRF9160 I am having trouble figuring out how to bring up the board.
I am using Azure IoT hub and can successfully build an application that can connect...
Hello,
I want to use the bq274xx.c sensor library. The bq274xx battery fuel gauge has an interrupt pin, which would allow to have the CPU idle until something interesting...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi there everyone I am new in nRF development. I was recently trying to add conexio stratus pro but i could not find it in my VS extension. What could be the issue?
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi,
I really like the new Zephyr conn_mgr, it is really easy to use, almost UNIX like. I am wondering what is now the best way to control PSM. Will CONFIG_LTE_LINK_CONTROL...
I have a timer int callback like this:
void pwm_all_handler ( nrf_timer_event_t event_type , void * p_context )
{
if ( event_type == NRF_TIMER_EVENT_COMPARE0) {
...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hello everyone!
I have a question about flashing firmware to a PCBA with the nRF54 and nRF91, or any dual MCU board in general.
When looking at the Thingy91(x) this...
