It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
When the central and peripheral is connected, we can get the RSSI value through sd_ble_gap_rssi_start() function. but how can I get the RSSI value when not connected (scaning...
Update: I've worked on the BLE arduino sdk from Nordic, and followed all the directions, but I'm having some compiler errors. I've crossposted to a different forum for more...
I am using pstorage library to keep some data in NVM.
Should I use some nrf_delay calls while using pstorage_clear()?
I am calling pstorage_store from callback function...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
From the documentation for the sd_ble_gap_sec_info_reply() function,
"This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times...
Dear Madame/Sir
From my client I received nRF51822 DK.
See att file.
I do not see Product Key for DK
How can you solve the problem ?
Redards
Valeri Tosev
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
We wish to make a universal device that may used
for ANT with the nrf51422 and the 32kHz crystal.
or for BLE with the nrf51822 without the 32kHz crystal.
Will there be...
