Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
Hello,
I am running a nRF51822 rev G0 with Soft Device 6.0.0 & SDK 5.2.0. My device implements a custom service with 4 characteristics. One of those characteristics is...
HI,all!
In the funtion on_ble_evt(), there is one of the events named "BLE_GAP_EVT_TIMEOUT", can someone please tell me what situasions might cause this event? (be better...
When the central and peripheral is connected, we can get the RSSI value through sd_ble_gap_rssi_start() function. but how can I get the RSSI value when not connected (scaning...
Update: I've worked on the BLE arduino sdk from Nordic, and followed all the directions, but I'm having some compiler errors. I've crossposted to a different forum for more...
I am using pstorage library to keep some data in NVM.
Should I use some nrf_delay calls while using pstorage_clear()?
I am calling pstorage_store from callback function...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
Hi,
From the documentation for the sd_ble_gap_sec_info_reply() function,
"This function is only used to reply to a BLE_GAP_EVT_SEC_INFO_REQUEST, calling it at other times...
Dear Madame/Sir
From my client I received nRF51822 DK.
See att file.
I do not see Product Key for DK
How can you solve the problem ?
Redards
Valeri Tosev
