before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I am wondering where I can find the temperature dependent behavior of the ADCs on nRF51822. I observe the ADC readings vary noticeably even when the die temperature reading...
Hi Nordic,
Where is a bug in bsp.h nRF51 SDK 9.0.0 and I think it was were before as well:
LEDS_NUMBER equal 0 causing a compilation error.
In Line 59:
#if (LEDS_NUMBER...
it will try to lower the RF, TX power
Bluetooth is not sure what to do because the first time
What things do I need to solve ? ex)component, software,hardware...
Good morning,
I have already implemented my application based on nRF51822 and SD110 v8.
In what regards bonding, I use a static passkey and it works fine.
The product has...
I will use the functions in app_timer to set a timer to fire every 3 seconds. I want this to occur "forever" (e.g.until a restart of the nRF51).
To avoid a timer overflow...
Hi,
I am using the nRF51-DK board as a central running with ble_app_multilink_central_s130_pca10028 sample application. I am using SDK version 9.0 with Keil 5.14 version...
Hi all! I am using the nRF51 DK and I am trying to use the elements demo APPs that Nordic provide - the Beacon app. after the downloading of the app and watching it working...
Hi
In my application, I use some of the IO pins for a multi-purpose sensor interface, that I would like to be able to configure when the application is running. The interface...
Hi,
Can anyone help me where can find the example ble_hr ? I have changed the main file and it is saved and now I want the original example that was in C:\Keil_v5\ARM\Device...
I have IAR Embedded Workbench 7.40 installed with nRF5x_MDK_8_0_3_IAR.msi. However when i select nRF52832_xxAA i get the below message:
WTD: Unavailable option selection...
In IAR Embedded Workbench for ARM, version 7.40.3.8938 (w/ common components version 7.2.4.3784 ) with nRF5x MDK for IAR version 8.0.3 .
When selecting the target in General...
Hi,
I have a couple of nRF Beacons and want to change the program so that it scans for iBeacon packets before starting to advertise.
The flashed program is just advertising...
I just would like to test my new nRF51 DK using the SDK V9. However, I could't build the "blinky_blank_pca10028". It always shows the following error.
Error: *** Project...
Hello,
I m using the UART in low power flow control mode(app_uart library). When the CTS line is asserted, what is the maximum time that the UART module takes for the UART...
