Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello,
I am currently optimizing the throughput for my mesh network and I am wondering whether I've hit the limit of what's currently possible. I have two methods for sending...
I want to measure the RSSI strength of my Bluetooth module, in various distances and situations.
I read in the description of the app nRF Master Control Panel that:
...
I'm trying to change the mac address of my nRF51822 chip using something like:
ble_gap_addr_t m_address_1;
m_address_1.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE;...
Hi,
I use GCC for compilation and nrfjprog for flashing. A few weeks ago I needed to switch on compiler optimization (Level 1) because my code grew a little too big. Now...
Hi,
I would like to have several nRF51 development cards connected to my computer at the same time using the USB debug port. The serial port and the RTT port work when several...
Hi,
We are trying to develop application with OTA DFU on nRF51. And we need to build bootloader ourselves. We use gcc for development. We found the bootloader example for...
I tried to run beacon example (from SDK 9.0). Even after uploading hex file I was not able to "see" becon. I'm using st-link v2 and openocd. Let me tell a bit more about what...
Hi,
I'm making device with nrf51822 chip and 400mA battery.
It connects to smart phone.
It has to calculate heart rate and some other things, so it's doing it on device...
Hi All,
I just bought the Nordic Semi nRF51822 DK (without the starter kit). I tested the Heat rate monitor app and it worked fine. It could send some random values to...
Dear all,
I tried the example program ble_app_uart given in the examples section of the Nordic folder in Keil installation. I created the hex code and programmed my chip...
I was just at the Nordic nRF52 Global Tour in Atlanta and I received the nRF52 Development Kit (PCA10040). One of the Nordic engineers mentioned that the nRF52832 is at rev...
Hi all,
I am using the BLE nRF8001 and EFM32 (ARM Cortex M3). I used the following SDK for connecting the modules using ACI (SPI). github.com/.../ble-sdk-efm32
Now I...
brownout reset = 1.7V
Operating conditions VDD(Supply voltage,internal LDO setup) = 1.8V
(by 1822 Product Specification)
In between 1.7V of 1.8V, or it would have been...
Greetings, I've been using the ARM GCC tools for about 2 months with success for programming the NRF51 DK board. Now I would like to try out the example found in:
examples...
