Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
this is how I initialize and enable LPCOMP
nrf_drv_lpcomp_config_t lpcompconfig = {
{NRF_LPCOMP_REF_SUPPLY_SEVEN_EIGHT, NRF_LPCOMP_DETECT_CROSS},
APP_IRQ_PRIORITY_LOW...
Hi,
I wonder if BLE_ERROR_NO_TX_BUFFERS(s110) and BLE_ERROR_NO_TX_PACKETS(s130) have same meaning.
These marco variables are defined in ble_err.h.
Thank you.
HI,ALL,
i am so sorry for my silly question here.
In ble CORE SPEC,
i saw a sentense (Version 4.2 [Vol 1, Part A])below:
"Device L is shown in the same locality...
Hi,
The SDK6.1 bootloader seems to have problems when used on a Laird BL600 module.
I'm using a BL600 with the SDK6.1 and SD7.1. I want to implement the bootloader in...
Hello!
As per documentation, RSSI is measured during the time, when particular packet is being received. In particular, nRF51822 Product Specification v3.1 states RSSIperiod...
Hi, i have a NRF51-DK (nRF51822 - PCA10028) board and using SDKv10 with SoftDevice S110.
I read everything i could find about this topic and i see people claiming data rate...
I am looking to synchronize collecting of data from outside devices with the connection interval of the nRF51822 and the S110 vers. 8.0 softdevice. Are there specific events...
I want to send big amount of data (10kb) with characteristic of 16 bytes. when the phone side is subscribed to notification I run a loop of data sending.
how can I synchronize...
I have read through the forum on this and I am still not completely clear. Here are my questions:
Can I create characteristics that are larger than 20 bytes? The Bluetooth...
In looking at the nRF51 UART Example I'm wondering about data loss over the Bluetooth interface.
When bytes are sent to the host, is there a re-transmission mechanism somewhere...
Hello,
I was just editing the handling of sent packets and I wanted to evaluate the contents of the ble_gattc_evt_write_rsp_t struct which is part of the BLE_GATTC_EVT_WRITE_RSP...
Hello,
im using NRF 51822 with SDK 10 / S110 8.0. Im working on a project that includes one or two timers (initialized by APP_timer function), the ble calender (like discriebed...
Hi,
Because I didn't want to keep with the last question when this is a tottaly new one, so created another question.
I've tried to get this project to work:
github.com...
We have a communication problem between nRF24LU1+ and nRF24L01+ chipsets. nRF24L01+ uses STM32F4xx MCU on board.
Is there an RF sniffer that sniff the protocol?
