Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I have have one ble project which is using softdevice s110. so that i want to extend this project by adding DFU service to it like shown here
devzone.nordicsemi.com...
hi,
i have PCA10028 dk board. i want to flash code in this board using dfu. i have generated Zip file(both soft device and application(example ble_app_hrs example)) using...
I am using this DFU library github.com/.../IOS-DFU-Library . On iOS 10 while processing DFU I receive error RemoteInvalidState in didErrorOccur method with description "Device...
I want to know the maximum range for major and minor in Ibeacon frame, as it is of 2 byte can we set any values from 0 to 65535 or is there any limitation.
Hi everyone!
I'm using the nrf_soc API for get random numbers from the rng and erase and write the flash memory.
In my code, I include the nrf_soc.h file, in the header...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
Hello,
I tried to do DFU using MCP 3.10.0.14 and I'm getting the error:
"Error during firmware upload. Timeout while waiting for response for START DFU"
How do I increase...
I have secure dfu working on the pca 10040, and being able to download my own signed app.
However I want to turn NRF_LOG and at link time I get several messages of "._build...
Hi,
my application consists of long waiting time without connection (hours, possibly days, weeks), then a central connects and downloads data, and then again long waiting...
Hello all!
Sorry for what might seems an obvious question, my skills are what they are :-).
We have a small circuit based on nrf51822 chip.
Our software is currently...
Hello, I am new to embedded world.
I wanna know that how do i create a new template/blank for programming in uKeil?
Right now, i directly open an example from the SDK...
Hi there,
I am currently working on a project where I would need to use the Segger J-link needle programmer with 6 pin header. We have produced the board and after following...
Due to the PWM driver having intermittent issues we had to replace it with a TIMER/PPI/GPIOTE setup.
The PWM is working great in this way, but now I'd like to have one of...
Hi All,
i am using Stpm32 energy meter board.
i have gone through the data sheet completely.
i want to read and write the register values
i am trying to write 0xABCD...
Dear All,
we have been working on a very small PCB design using nRF52832. Some time ago, in another thread , I asked for an Eagle footprint for an antenna and got the quick...
