Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi
I cannot find the minimum pulse length to trigger wakeup using DETECT from GPIO hw pin configured as SENSE pin in the data sheet for nRF51822.
Ex: set PIN_CNF[0].SENSE...
Hi,
I tried DEVICE_NAME with a AABBC Ddddff Tttttth Vs DEVICE_NAME as AABBC. The time taken to connect with a longer device name takes at least 3 attempts (in the sense,...
Dear Nordic Team,
Thanks for support.
I want to merge softdevice hex,application hex and bootloader hex. I am using windows 7 OS and my SDK version nRF5_SDK_11.0.0_89a8197...
When a nRF52 BLE as peripheral had connected to a BLE device as Central, if the nRF52 BLE also coule connect to other BLE device as Central at the same time with the supoort...
Dear Nordic Team,
Thanks for support.
I try to make zip file generation using command promt as per the nordic document(How to generate the INIT file for the DFU.pdf...
I want to test RF during production but I do not have any GPIO or UART points on my DUT so I don't want to run the DTM. Can anyone tell me what problems there are with this...
Hi:
I reference rate meter program：
“nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu”.
After function "device_manager_init"，I handle...
HI,
I am now trying to use nrf51_iot_sdk_0.8.0_f1f6187. And I have run example application in nrf51 iot sdk on nrf51-dk board. It works fine.
Now I want to develop on...
I want to send a service changed indicate after upgrading app by dfu.I know dfu already so that,but i don't know that how dfu do that.
there is service_change_indicate...
I used to able to get the blinky example in SDK11 to work. But for some unknown reason I couldn't scan my device using Nordic master control panel. The LED1 will be turned...
Can the nRF52 output the 32.768kHz clock on a GPIO. If so, do I need the 32.768kHz xtal, or can I output the generated clock from the 32MHz xtal? I need this clock to sync...
Hi
Yesterday I downloaded the new SDK12 and checked what changes could be relevant for my ongoing/next projects.
One remarkable thing was the fact that almost any peer...
Hello,
I'm trying to upgrade the application on my board via OTA DFU but it seems to fail if the app file is greater than 64KB:
DFU fails with my app which is 70kB and...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
