Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
Previously i've been using the nRF dongle using the BLE NUS Central example to communicate to another nRF DK with the BLE NUS Peripheral example via serial/termite and ble...
Hi there,
I am new to the nRF world and I might be asking a very stupid question with obvious answer but I couldn't find any hint from the Infocenter nor the Tutorials...
Hello guys,
I followed this guide to set up the software on my macbook.
The blinky example can be successfully built, but cannot be flashed to the nRF52 DK. Then I tried...
Hello everyone,
I tried to rename(right click the project name and click the "Rename") my project from "sdk11_ble_tutorial_adverstising" to "sdk11_ble_tutorial_adverstising1...
Hi,
anyone would have any idea (to look at, as to) why the same app running on the same chip/PCB (nrf51822QFAAH rev3) could possibly have slowed down so massively after...
I'm trying to add debug information to ble_app_hrs using nRF5 SDK 10, softdevice s110 version 8.0.0, building for an nRF51-DK target (PCA10028) using ARMGCC. I've found that...
I've encountered a problem getting the tick count from FreeRTOS when tickless idle is enabled. I'm not sure if this is a bug or just unexpected behavior. I am using the latest...
Hi everyone,
I'm integrating the spi_master_with_spi_slave example into our firmware; however, I'm not seeing the event callback I registered being called. I'm verifying...
Hi everyone,
I implemented nrf51 flashing through SWD (external MCU is used). After first flashing and reset when we enter debug mode on SWD second time we have a busy...
Hello,
I am trying to interface an MPU 6050 with an NRF52 with sdk vs 12.0. I noticed in the mpu6050.c file that it uses a twi_master.h file in the sdk in folder labeled...
Linking ble_app_proximity_pca10040_s132.elf
Output/nrf52832_xxaa/Exe/ble_app_proximity_pca10040_s132.elf section `.fs_data' will not fit in region `UNPLACED_SECTIONS'
...
Hi,
I flashed an board with a NRF52832-QFAA-R7 with the ble_app_hids_mouse of SDK 12.1 (and also with the keyboard) example to test and build an application using this...
Hi,
I've been trying to get an implementation of the HTTP Proxy working with nRF52. The nRF52 is in central mode, accessing the proxy (running on a Pi with Bleno) which...
i measured the current of nrf52 dk board with the spi example (examples\peripheral\spi\pca10040). the result shows that it consumed about 6 mA !!!
i read the nrf52 datasheet...
Building ‘ble_app_cscs_pca10040_s132’ from solution ‘ble_app_cscs_pca10040_s132’ in configuration ‘nrf52832_xxaa’
Generating linker script ‘ble_app_cscs_pca10040_s132.ld...
