Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
Am starting custom service to support custom profile and it works without any issues.
But when I add DFU service also to start after custom service DFU service fails...
Hi All,
I have a question about use of super/ultra-capacitor in a circuit using a module BLE (nrf51822 inside) instead of accu Li-Pol / Li-ion ?
it is possible to use...
I am looking to use the nRF51822 in my product and have been given a nRF51822 development kit however i have been looking for access to the Firmware and Hardware files and...
I have an nRF52 DK and have compiled (with gcc) and flashed an example that contains the line
NRF_LOG_PRINTF("SPI example\r\n");
I get the appropriate LED flashing...
Hi,
I'm trying to discovery the content of a vendor specific GATT service.
So far I'm receiving the BLE_DB_DISCOVERY_COMPLETE event and I'm able to see that I got 4 entries...
Hello,
I have a BLE Nano (nRF51822) and I want to develop an app which will find all BLE devices around (MAC addresses and RSSI) and send it by UART/SPI . I've used nRF...
Hi.
I'm using nRF51822AC, S130.
I made source code for RF test as below.
NRF_RADIO->SHORTS = 0;
NRF_RADIO->EVENTS_DISABLED = 0;
NRF_RADIO->TEST = 0;
NRF_RADIO->TASKS_DISABLE...
I tried MQTT subscriber example code, it compiles and loads successfully but it doesn't show the LED lights accordingly as I press the buttons, meaning that MQTT state is...
I am using S130, and I try to write an very simple program, when I push button_1 then it read ADC and print it our by UART.
So, write a "nrf_drv_adc_buffer_convert" code...
I connect to nrf51 DK board and PC using USB. I used RTT Viewer to see RTT log output.
But when I try to compile and download from keil to the board, I got several WARNING...
All,
Can anyone tell me what is the fastest time that a ble SD (5.x / 6.x) running on an nRF51 can (re)start advertising from a disconnect. Basically looking to do an ...
I am not able to connect Garmin Edge or SimulANT to nRF51-DK. Neither sensor nor receiver seems to work. Just looks like there is no RF.
Examples tried:
power_only_sensor...
Dear Sir,
Here I test the ble_peripheral example "ble_app_uart" (Softdevice 8.0) with Kail MDK ARM 5.20 environemt on the PAC10028A board.
I found it's not stable and...
