Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I notice that the track which runs from P0.11 (E4) is connected to GND at pads C3 and C4. Is this intentional? If P0.11 is required for GPIO usage, is it necessary to go to...
I am trying to update my project to SDK 12.2 which was released this week and I am getting a ton of compiler errors with the FreeRTOS source files. For example, I try an compile...
I'm a begineer in nRF52DK and S132.
I am trying to make an application code to enable link layer control procedures at any time in a connection state with the nRF52DK and...
hello everyone，
Which APP demon is the most stable APP？
I use nrf-master APP to test the blue device，it can connect very well。but when I use uart-app ， it can't connect...
I notice that if Make virtually any of the SDK12 armgcc examples that I get a warning that 2 include folders do not exist
e.g.
../../config/ble_app_hrs_pca10028_s130...
BLE UART run example runs in debug mode and able to see the BLE in the nrfconnect
using Jlink debugger
When the Jlink debugger and power supply is provided we are not see...
Hello,
I am currently using the GPIOTE Driver (nrf_drv_gpiote) to detect external interrupts from a sensor on a custom board using the nRF51822 with the S130 v2.0.0 SoftDevice...
Hello,
I've an issue with several smart-phone models when I use the softdevice S130 v2
I did tests with PCA10028 and the example "ble_app_bps".
I used softdevice...
I use app_button with simple handle function. When button is pressed the led is on, when released the led is off. Everything works fine, but after some random number button...
Hi all,
I am having issues with the BLE DFU process with both nRF51822 and nRF52832 (with different applications).
I use the nRF Connect application to update my device...
Any idea why sd_ble_gap_rssi_start(handle, 0, 0); returns NRF_ERROR_INVALID_ADDR ? The documentation doesn't list that as a possible return value and I can't look in the code...
I write the code almost ok.
but , I neet the DFU function to UPDATE THE software .
Now, we only find a v11 example can run ok but only a zip, not including any code. ...
Hello,
First of all, I've read the entry below.
devzone.nordicsemi.com/.../
My questions:
1 - If I cannot advertise for only specific masters, how can I provide...
Hello!
I have a problem with NRF8001 modules. I have two similar boards - one with NRF8001C and another with NRF8001D module. NRF8001C board works well, but NRF8001D board...
