Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi NORDIC
I download the example of multilink central (S120) into nrf51822 . I do not know why it can not work ? My SDK is s110_nrf51822_7.0.0_softdevice . Please help...
i am very confused about how to count pulse by using nrf51822? I am going to make a heart rate counter, but i don't know how to config registers to achieve this function....
I can't get a simple application, no soft device, to debug on the nRFDK 10028 board using the I-Jet. I am using the debug in and powering the device from an external power...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all,
I am using the multi role example ( github.com/.../nRF51-multi-role-conn-observer-advertiser) to scan and advertise concurrently.
I was wondering if the scanning...
I have a 16MHz external clock oscillator to drive a micro controller in my system. Can this also be connected to the crystal input on the nRF24L01+ to drive it's clock? Should...
Hi All,
I wanted to write a patient record to glucode measurement charateristics from android Phone which supportes BLE features . How do i write a record to BLE device...
When using the OTA DFU using the button press implementation is it possible for the bootloader to require bonding? I figure I can use the preserve app data functionality built...
Just took the developer.mbed.org/.../ code and run it on the board.
But when I try to connect with my phone I get: "Device doesn't support UART. Disconnecting".
What...
Hello,
I am using the RedBearLab's BLE Shield 2.0 and I'm trying to modify the advertisement data using nRFgo studio to include manufacture data (type: xFF) for one of...
Our IC nRf51822 has an identifier "QF AA CO" (IC rev 1) The document "nRF51 Series Compatibility Matrix", Table 4, shows the maximum version of the SDK 5.2.1 and 4.4.2 SD...
Hi guys,
I install V1.6 nRF ToolBox apk in my Android phone, and want to do the DFU operation.
When the device in DFU status, I select the target HEX file but it shows me...
We are configuring the watchdog like this:
// Watchdog
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Run << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Run << WDT_CONFIG_SLEEP_Pos...
