Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
we want to use NPM2100 with 2.4V rechargeable battery, burst 2.4V to 3.3V @150mA.
there are a sepcial charger solution for the 2.4V rechargeable battery .
Could Nordic...
Hi,
I'm attempting to upgrade an existing project (which is still in the development stage) from NCS 2.7.0 to 3.0.2; this seems to break native TLS, and I'm not sure why...
Hi, I've encountered a change in behavior when upgrading from NCS 2.9.1 to NCS 3.0.1 regarding MCUboot and watchdog integration. In NCS 2.9.1, I was able to enable the watchdog...
Hii everyone,
In a project. I'm trying to add dfu to a central and peripheral project. While doing I come to know that dfu using device_manger calls for its processing...
Hi,
I want to use the RSSI feature for CCA, i.e. measure background signal strength. The radio is started in RX mode, then I use the following code to get one RSSI sample...
Hello,
i implement the CTS_C example in my application.
I get the correct time Output in the UART.
Is this time the running in the Background?
How can i check if is...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
IN COMP of 52832, I find that a current source around the COMP form a OSC with a cap. I want to know what is the use of this OSC. And can the current source be disabled if...
I have a few characteristics under a service, and I'm trying to store the value if any of these characteristics is written to. However I run into an issue where if I enable...
Hi !
There is one thing I don't understand with the led included on the NRF51-DK board.
According to this thread ( devzone.nordicsemi.com/.../ and the datasheet it seems...
I want to take saadc samples for one second,every 5 seconds,the rest of the time the mcu is in system on sleep mode with rtc1 on.Eery 5 second there is an rtc event and the...
As the datasheet showing
The GPIOTE input mode consumpt upto 22uA ,it is inconceivable.I want use NRF51822 to design a ultra low power consumption production ,and use...
HI:
I want to use nRF24L01+ as TX, and nRF51 Dongle as RX. And I try to use nRF51 Dongle to just listen for the RSSI of the NRF24L01+. Is there any example or reference...
Hi, I am new to nRF51DK. I am following this tutorial shown below:
developer.nordicsemi.com/.../a00066.html
After I flash my s130 softdevice, I follow the file directories...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
Hi, i am designing a board using balun in it. Also, i am going to use meander antenna of nordic dongle(reference image is attached). As i can see, there is no RF coplaner...
Hello , I want know , if i used the Gazell Pairing Library (gzp) , it means that I can not use the ACK
Payload function ?if i can use the ack payload function place give...