Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hi,I am working on Eddystone project i.e nrf5-sdk-for-eddystone-master and tested it on NRF52(PCA10040) development board it advertising Eddystone-URL frame successfully and...
hi
i have nrf51422 v2 that use sdk v6 and s210 v3
when i download an example on my nrf and run it to see error check its not returning anything
in s110 i have error...
Hi, In my custom project I need to add two 128-bit uuid services and also I need to use pstorage to protect the application data from power loss. But I got the problem is...
Hi,
While working on OTA DFU using my custom code compiled to work on PCA10028 board, I am seeing the following issue.
The OTA DFU works fine using Master Control Panel...
Hi,
I'm designing an antenna for the NRF52 but with some different conditions, the antenna will be under a silicone superstrate and this will change the impedance of the...
Hi..
Everyone,
i am using nrf52 with softdevice 132.
i used peer manager.
i am able to able to flash softdevice, bootloader and application.
but after that application...
Hi,
I've built a device using an IMUduino board, which is supposed to be similar to Arduino Leonardo board with a nRF8001 bluetooth. I was able to connect my device to...
Hi all ...
My product uses multiple BLE peripherals (Simblee by RF Digital) communicating with a common BLE central to time events detected via sensors on the different...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
So the nRF51822 has one 32 bit, two 16 bit timers and two Real Time Counters.
What is the difference in a timer and counter? The timer API seems to hard link RTC1...
Hi,
In my project I am using nrfutil.exe tool to create a .zip by using the following command
nrfutil.exe dfu genpkg j1.zip --application application_nrf51822_xxac.bin...
I'm running into a weird problem where there is a long delay that is variable between calling ble_conn_params_change_conn_params() and receiving the BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
I've got a problem with my nRF51 DK. When I attach it to the USB port the drive doesn't appear on Windows explorer and green diode doesn't flash too.
I've been...
By design, the TI LP55231 LED driver IC will fail the TWI write of the reset register (0x3D). It's necessary to reset the IC in an edge use case. I'm using the nRF51822 HW...
