We are developing a very low power product. In some cases like not getting registered, PSM not being available, ... we want to drop the connection and go to a sleep state...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi,
I'd like to know how can I implement a Scene Server for one or more Generic Onoff Servers (typically leds).
I read the documentation related to Scene Server and I...
Hi,Team,
I am developing pawr using nrf54l15-dk. I wanted to set the parameters of pawr with 128 sub-events and 8 response intervals, but the setting Failed and the error...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
I have two device , one is Tx-Device the other is Rx-Device.
Tx-Device : Auto continued Send 4 bytes data to Rx-Device by Radio.
Rx-Device : Using Radio Interrupt receive...
First of all I'm a BLE novice, so sorry if I'm asking obvious questions. I've built a home project where a battery powered mcu listens for requests over wifi and drives a...
Hello.
I'm trying to do as follows: ONE button used either to wakeup or to put system to sleep. In general almost everything is working but I cannot find how to configure...
HI,ALL
as i known, the BLE key is a six digit pin.
and in the static void device_manager_init(bool erase_bonds) ,the statement shows below:
register_param.sec_param...
According to this post , and this GitHub source file , in the nRF51 chip's mbed implementation:
The ADC reference voltage is 1/3 power supply
read_u16() seems to...
HI,ALL
in the nRF5_SDK_11.0.0-2.alpha_bc3f6a0 , GATT Server Event IDs.
i do not find the read event.
All i found is the BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST .
Now...
Hi, all
Recently I use nrf51822 CEAA, WLCSP package to develop a project on UV (ultraviolet), the UV sensor must be exposed to the sunlight. When we take the product board...
I'm running the DFU example from the nRF5110.0.0 SDK. dfu_dual_bank_ble_s110_pca10028 on the DK and it works perfectly using Master Control Panel, but it does not work from...
I currently have a dualbank bootloader setup and I'm trying to change it to singlebank. If I burn the singlebank bootloader with the jlink it works fine, but if I use the...
Hello,
I modified ble_nus_c to manage multiple connections.
The first time (first client) i call sd_ble_uuid_vs_add in init, it returns OK. The second time ERR_NO_MEM...
both for APP_UART_FIFO_INIT and APP_UART_INIT i never receive APP_UART_DATA_READY
but at least i get APP_UART_DATA sometimes .
most of the times i get APP_UART_COMMUNICATION_ERROR...
I'm trying to monitor the time a signal is high/low on a GPIO. It seems to work alright with timers and PPI, but I wish there was a way to reset the timer upon capture.
...
Hi,
What is the largest possible value of "MAX_VAL" for application timer given below:
"#define APP_TIMER_PRESCALER 0"
"#define M_DELAY APP_TIMER_TICKS(MAX_VAL, APP_TIMER_PRESCALER...
Since UART-BLE is an emulation of UART on BLE, is there a need for physical wiring of the pins (RXD, TXD)? Assuming I'm not using RTS/CTS as I have disabled flow control,...
