hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello!
I was copy template project from preinstalled folder to the desire one. When I opened program in new folder, the translate operation work fine. But when I pressed...
I would like to configure the connection timeout with the S130v1. This timeout is described in the following sequence diagram: infocenter.nordicsemi.com/.../group___b_l_e___g_a_p___c_e_n_t_r_a_l___c_o_n_n___m_s_c...
Hi there,
In the process of moving from SDK 10 to SDK 11, I've also been migrating an accelerometer driver over from using straight nrf_drv_twi code to the higher level...
Hello,
Is it possible to use easyDMA to transfer from GPIO to memory without involving the CPU? We need to read from a parallel bus for a short duration, without losing...
When setting up a 1Mhz square wave using NRF_PWM on the NRF52 or GPIOTE on the NRF51 while BLE is advertising, the PWM stops when the radio is active. The problem doesn't...
Hi,
I'm developing a BLE application for the nRF52 and I wish to use directed advertising and the whitelist.
I initialise the Bluetooth advertising using the following...
I have been using softdevice S130 version 2.0.0-7.alpha with SDK 11 in Keil using the pack installer. How do I change my project to work with the updated version that doesn...
Hi,
I believe there's a minor bug in low_power_pwm.c regarding pwm_state.
The routine low_power_pwm_start sets the pwm_state to NRF_DRV_STATE_POWERED_ON ; but it then...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I am troubling shooting some issues between my device and iPhone using nRF Sniffer.
One of the errors the sniffer captures is this:
Master to Slave: Rcvd Read By Type...
I will be using the nRF52 adc from -20C to 85C and am trying to determine if I need to calibrate and if so how much temperature difference I can have before it is time to...
Hi, I'm working on the nRF52 with S132 v2.0.0.
I am using a self-implemented "connection manager" that tries to establish bluetooth connections to pre-configured auxiliary...
Hi,
I am using 2 x AA batteries which gives 3V. Planning to enable all the internal LDOs (1.2V, 1.8V and Radio LDO).
VDD and AVDD are shorted on Board.
Will the device...
Is there a porting guide to this?
Custom hardware
Central device
SDK V11
I'm getting a reset in client_handling.c::ble_stack_init();
Right after I set the clock as...
