Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Based on the announcement for upcoming training ( www.nordicsemi.com/.../Bluetooth-Innovation-Trainings) it sounds like Nordic will support the Bluetooth SIG's Bluetooth Developer...
Hi, Is there a UART bootloader built in to the factory firmaware similar to others like NXP LPC series where a specific pin is held low at reset. If so what pins are used...
Hi, Nordic Engineers:
Pls give your hand, new question: Could i run two app on one mobile-phone that connceted with only one device? also, they can operate the device by...
Guys, I would like to put the internal uC in sleeping mode while nRF51822 is advertising and wakeup him, when I establish a connection.
I know that is possible, it must...
Alright, so I am having a lot of trouble generating a valid zip file to update with nRF Toolbox (android).
I used nRFgo Studio to flash dfu_test_app_hrm.hex and dfu_test_bootloader_b...
I got a Tablet running Windows 8.1 with a Bluetooth Module that is able to find my nRF51-DK.
Is there a software I can use to interact with my Bluetooth Services of the...
I am currently developing an IoT device using nRF8001 which needs to report gas concentration obtained from a sensor. I have looked through the standard GATT profiles , and...
Hi,
I am having trouble understanding the new PACK structure in a project, in particular, with the example project dfu_dual_bank_ble_s110_pca10028.uvprojx.
My setup...
Hi,
I would like to know what is the footprint of softdevice S110 v8.0.0.
When i compile the Glucose code example from Nordic it shows a Program Memory utilised as around...
According to the device manager the length in bytes returned by sd_ble_gatts_sys_attr_get() is:
((ATTR_SIZE * (CCCD_COUNT + 1) + CRC) * 4)
When I call sd_ble_gatts_sys_attr_get...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hi
I am trying to change the radio's transmit power in program, but I can't solve it.
I downloaded nRF51822 Beacon v1.1.0. and am testing PCA20006. (Source Code\nrf51_beacon...
Hello,
for my sensor I need to have a delay BEFORE pulling CS high. So I would like to add an argument to the
spi_master_send_recv()
function that give me exactly...