Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hi All,
About DFU.
I want to know about UART DOWNLOAD for nRF51822 with S130.
Can I download the firmware via UART for nRF51822 with S130 ?
It's not OTA DFU.
...
I wanted to know what's the maximum data throughput if one device has both roles (Client/Server) working at the same time. I already saw the tables for the different SoftDevices...
Is there another IC I need to integrate into my board to allow the chip to be programmed through USB? Also, is the same true for programming OTA? I understand that I will...
Is there anyway to enable the UART on a NRF51822 to be 7-bit data instead of the default 8-bit?
Lowest level driver structure I could find is
NRF_UART_Type (nrf51.h...
I'm using Master Control Panel for PC to try to test bonding with MITM security on the peripheral I'm developing, and I suspect there's something wrong with the Master Emulator...
I am using the nRF52 in 2Mbps proprietary mode. I am running my own custom stack to maximize data throughput. There are no re-transmissions in my design. I have a loop of...
In sample code for central devices,, the BLE event handler, on_ble_evt() , handles the `BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST' by accepting the request. Is it possible to...
On pages 49-50 on the nRF51 Product Specification, in section 8.5.2, there's a bunch of current consumptions listed for the Radio with the DC/DC disabled.
Do those values...
Hi there,
I was hoping to first pull the SD version and application version from the device before I attempt to send an update.
Are these values exposed anywhere within...
LAST EDIT AT END OF POST
We are using a custom board with an nRF51822 programmed with a modified beacon application (which worked several months ago). After opening MCP...
Hi,
Everyone,
I am Using S130 and sdk 11.0.0.2-alpha with nRF51422 chip.
I have two crystal in my custom pcb,
one is 32 Khz crystal for LFCLK between XL1 and XL2 (pin...
My application is using the FIFO UART module to communicate with another MCU. It is also running softdevice S132 v2.0.0.
While most of the time everything runs smoothly...
Hi
Are there any major OSes/stacks (e.g. Linux, Android, iOS) that provide support for the L2CAP feature so that we can test our Nordic device against?
Thanks
Hi,
I would like to know what is wrong with my code, which is presened below. Each time the timer is triggered I would like that the program writes four bytes into the...
