void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
Finally, after some struggle, I achieved to port the bootloader to s120 V2.1.0 and work just great on a dev. board with nRF51422. But now I have another problem...
Hi, i hope i'm not duplicating any questions, but i couldn't find a similar one.
I worked with other ARM micros in both mbed and Keil before, but i'm new to Nordic Semiconductor...
Hello,
I getting started with nrf51 DK.
I followed with many blogs.
I checked errors, and fixed. And I builded the example 'blinky'
But my nrf51 is not blinked.....
Hi all,
I am doing the PTS and meet some issues here:
Using the SDK 8.0 KB demo with SD8.0;
Do the profile test with PTS dongle and tool, and return errors on...
Hello everybody,
I'm using NRF Beacon (51822) board, sdk 6.1.0.0 and s110, problem is when I enable whitelist and add the Bluetooth address of my phone( 74:51:BA:F7:60:9F...
In my bootloader I'm using sd_flash_page_erase() directly without pstorage.
The flash erase performance is exceedingly slow. It is taking 13.187 seconds to erase 132 pages...
Hello!
We are thinking about creating some devices for Apple HomeKit.
But devices for HomeKit have to go through one thing: Apple certification. And one part of the certification...
Hi
Maybe silly question:
I was wondering: if I cast a pointer to a uint32_t to an array "buff" of uint8_t, what is held in buff[0], MSByte or LSByte?
Or in other words...
Having just upgraded to the Soft Device 6.0.0 and SDK 5.1.0, I can no longer flash my nRF51822 from Keil. I get this in the Keil console:
Load "C:\\Users\\Eliot\\dev\\nrf51_sdk...
Hi,
I'm designing a four layer flex PCB with the nRF51822-CFAC and recommended ST BAL-NRF02D3 balun and PCB trace antenna (not chip). I have a couple of questions.
...
Greetings,
Using the "central multilink" example project, how do I stop scanning if no advertisers are found? I see a case BLE_GAP_EVT_TIMEOUT in function on_ble_evt() but...
Hello
I found similar questions but no answer?
In the manual is written that I can control the parity bit in manual mode with the TXPARITY register but I can not find how...
what may be the reason for app_assert _callback error in s130,ble_central_and_peripheral that occurs from the following 2 lines
sd_softdevice_enable((uint32_t)NRF_CLOCK_LFCLKSRC_XTAL_75_PPM...
I have Rezence SDK working well with Keil uversion with wired and wireless debug without any issues on either nRF51 and nrf51822 DKs. When I port the project to Eclipse with...
Using the bootloader example code in SDK 8.1.0 for gcc, roughly how long does it take from power on to the call to bootloader_app_start()?
My device is motion activated...
