Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I'm having a strange problem. I'm running the nRF51-DK with a dual-bank bootloader, S110 soft device, and my app under gcc. I'm using Eclipse Luna as my develpoment/debug...
When i added timer in my bluetooth code my board will not advertise.using pca10028 and nrftool box uart app on iphone 5s.
here is my complete code. Using timer1
Final with...
I'm using the 0.9.2 SDK SPI slave example to connect to a SPI master (Atmel SAM4S). When I initiate a SPI transfer from the master side I can see that all the data arrives...
Hello,
I have been going through devzone questions to figure out how to enable the default debugging messages through Putty for the ble_app_proximity example project from...
Hi:
I make the gazell ready, and I need an extern PA(RFX2401) for a long distance commuicate. But there is some trouble when enalbe the PA.
My function:
Host:
pin_Set...
Hello,
I am using ble_app_multilink_central example as a foundation of my app involving central - peripherial connection (S120 - S110). My app works nicely but i have problem...
Hello, I am trying to establish a connection between the nRF52 board and the USB serial converter TTL-232R-3v3.
The setup is such that I connect the converter cable to...
Hi all,
we have a project based on nRF51422, SDK 6.1, Softdevice S310 2.0.1.
We use the bootloader for DFU services. Our problem is to send a service changed notification...
Dear all, I had debugged example Heart Rate Service from SDK 9.0.0 without problems but I think we have a exception, when I insert a breakpoint on line 923 instruction APP_ERROR_CHECK...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
We designed our own board using nRF8001 and EMF32, I used the EMF32 development kit to test the code and it is working fine. When I down the same code to my own board, it...
Hi ,
I am planning to implement S120 UART to communicate with desktop as well as S110 UART BLE.
I browsed in the forum and found out we already have example in github...
I have a small nRF51822 module that I want to use for UART communication without handshaking, and I'm having problems with reliability. Basically the nRF51822 crashes and...
Hi, I've got a pretty basic question, but I haven't found a satisfying answer for it. It is obvious, that the CC registers are 32 bit wide, but because the RTC Counter is...
