Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hai ,
I need to update nrf52840 over ble from esp32 . first i tried with app , firmware gets updated .. as per the dfu protocol i understood flow and tried to writing data...
I need atleast 10 UART channels to be configured in my project. Is it possible to do it with the NRF52840. I believe because of the PPI I should be able to do this. I was...
I want to create a small bluetooth device with the nrf52823 chip. I want to use a lithium battery cell to power the whole circuit and therefore it neet to be low power. On...
I'm bigger of NRF52832 and beacon concept. I need modify my beacon data like Major,minor and Tx power change via mobile app configurable. please share any example code or...
I purchased a new nRF9160DK. Upgraded to latest 1.1.0 firmware. I built the AT application and can talk to the modem using the LTE Link Monitor application.
The DK came...
Hi, I'm working on nRF52832 at SDK ver15.3.
My problem is Current consumption increasing (82uA -> 550uA) when WDT Reloading in sleep mode.
I set WDT configuration "Pause...
I am trying to send and receive a response from a machine using Modbus (TTL to Rs485) and nrf51822.
Connections: R0 -> RX(P0.11) ,D1->TX(p0.09), RE&DE->P0.19,VCC->5V
Just...
Hey
We have successfully put the dongle into operation. We were able to develop and successfully test our software.
As soon as we test it with the JLINK on the module...
Hi
I have problem because i dont get all data which are in FIFO uart on my smartphone via BLE. Nrf as i can see in example sends data where data[index-1] == 0x0d || d ata...
I'm working with nRF52832 and playing around with some peripheral examples from SDK 16.0.
The FreeRTOS based heart rate sensor example ( ble_app_hrs_freertos) seems to work...
Hi.
We are using the Nordic UART service. Our project is based on the example project "ble_app_uart" from version 15.2 of the SDK. I've found after about 3 minutes it stops...
So I have been saving a structure using FDS and it seems to be working fine but after a while (2-3 hours of updating value every 10 seconds) the fds_record_update(); function...
CONFIG_MAIN_THREAD_PRIORITY=7
I read prj.conf of mqtt_simple. Why is the value of 7 given?
https://github.com/NordicPlayground/fw-nrfconnect-nrf/blob/master/samples/nrf9160...
Hello,
I am having issues detecting my board with some phones. I have tested it with a Samsung Galaxy S8+, Android 9, and with android 5.1.1. However, I can't detect it...
